Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Do not underestimate the forklift at the workplace. If the operation is not good, there will be severe crashes in mins, and there are several accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which nearly created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork should not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch other products or items. The lots needs to be stabilized with very little back tilt of the gantry to ensure that the lots does not slide backwards. The mast can be slanted ahead a little when the load is decreased to enable very easy positioning of the tons and removal of the forks. .
6. It is restricted to fork products at broadband and ram tough items with the fork head. .
7. When the forklift is functioning, it is prohibited for people to loaf the fork, so as to prevent the collapse of the goods and injure people. .
8. Straining is banned, and it is forbidden to make use of forks to raise employees to participate in high-altitude procedures to stay clear of high-altitude dropping mishaps. .
9. It is not allowed to use the brake inertia to slide, put, round or roll things. .
10. It is not allowed to utilize forks to select, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you must discharge the goods or lower the fork frame.
2. Pull the parking brake manage to dead or dispirit the parking brake switch.
3. The engine is shut off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the lorry's line of sight and does not go beyond 1 min).
4. Get rid of the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance ought to be examined, and gas, lubing oil and cooling water should be included.
2. Examine the safety and security efficiency of beginning, running and stopping.
3. Examine whether the lights and horn signals are complete and effective.
4. During the operation of the forklift, inspect whether the stress and temperature are regular.
5. After the forklift is running, the exterior leak needs to additionally be inspected and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you encounter a person in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving speed in the factory does not exceed 5 km/h;.
4. When driving, the low point of the cargo should be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be as well sharp to stop the tendency of " totally free turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the gradient. When the slope is greater than 10%, the lorry must be driven in reverse when going downhill;.
8. When the forklift personnel carry the goods and move forward, if they encounter big or hefty products and most likely to the chauffeur's view, they ought to take the turning around workout
.
The "Eight Prohibitions" should be adhered to in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to lift the goods for long distance driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It Stand-on Electric Pallet Stacker is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll objects.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When Electric Forklift Truck for Warehouse there is an obstacle on one side of the roadway, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844